Home > DIY Cables / Mounting / Misc > Extreme Strip / QuickTree™ Pixel MegaTree Mounting System >

QuickTree™ Pixel MegaTree Topper Mounting System
PRODUCT PHOTO: QuickTree Pixel MegaTree Topper Mounting System
Photos may show optional, separately purchased or customer sourced items
Product may differ slightly due to product improvements


 
Additional Photos:





Availability / Ships: Same Day, Sporadically up to 3 days (Delivery Time Information)
Product Code: 750

Select the String Count for The Topper

QT8 - 16 PixNode Strip Topper V2 (8.5" Overall Diameter / 1-3/8" Top Fence Rail Center Pole) [Add $21.99]
    - Designed for 16 Strip, 180 Degree MegaTrees of 8 to 25ft in height

QT2 - 5 to 32 PixNode Strip Topper V2 (8.5" Overall Diameter / 1-3/8" Top Fence Rail Center Pole) [Add $28.99]
    - Designed for 32 strip, 360 Degree MegaTrees of 8 to 25 feet in height

QT1 - 3 to 16 PixNode Strip Topper (4.6" Overall Diameter / 3/4" EMT Center Pole) [Add $11.99]
    - Design for MiniTrees or small pixel trees under 10 feet in height

QT3 - 10 to 64 PixNode Strip Topper (14.7" Overall Diameter / Custom or 1"+ Floor Flanges) [Add $69.99]
    - Designed for Super-MegaTrees of 20 to 40+ feet in height

QT4 - 21 to 96 PixNode Strip Topper (24" Overall Diameter / 1-1/2" Pipe Flange Support Center Pole) [Add $149.99]
    - Designed for High Density Giant-MegaTrees of 20 to 40+ feet in height

SEE CHARTS BELOW FOR DETAILED INSTRUCTIONS AND LAYOUT FOR ALL TOPPERS LISTED ABOVE

Center Pole Load Spreader (Optional)

Center Pole Base/Ground Load Spreader for 3/4" EMT or 1-3/8" Top Rail Tubing [Add $4.99]
    - See product page for more details on this item

Qty:  
[Product Description Page]
 
.
QT3 - Super-MegaTree Topper
QT2 - MegaTree Topper
How to Install PixNode Strip
Into the QuickTree Topper
How to build and size a typical
50 pixel string strip
Product Features
The Original QuickTree™ system from HolidayCoro allows you to combine PixNode Strips™ to build your pixel MegaTree in no time flat!

  • General Product Information
    • Designed for mounting HolidayCoro Extreme PixNode Strips™ and HolidayCoro Classic PixNode Strips™ to form an RGB MiniTree (QT1), MegaTree (QT2) or Super-MegaTree (QT3)
    • Only requires two simple zip ties for mounting strips - no screws, nuts or other hardware required and dis-assembly for off-season storage is just as easy - no screws, nuts or other hardware need to be removed during dis-assembly
    • Each topper has 3 or more combinations of string density allowing maximum flexibility or future growth without the need for new hardware
    • Ability to build any diameter or height tree from 4 to 40 feet in height or anywhere in-between
    • The design keeps the HolidayCoro PixNode Strips™ extremely close together to allow for the absolute tightest concentration of pixel strings of any topper in the industry, resulting in clean, "pointy" tree tops
    • Mounts with standard, inexpensive and commonly available pipe
      • QT1 - 3/4" EMT conduit
      • QT2 / QT7 / QT8 - 1-3/8" Top Rail Fence Tubing (Actual diameter of swaged pipe end is 1.17 to 1.25 inches)
        • Home Depot: 10ft Length
        • Lowes: 10ft Length, 10ft Length Black
        • Menards: 10ft Length, 20ft Length
        • For customers that wish to use 3/4" threaded "black pipe" for either the pole or the star attachment, there are pre-marked holes for flanges already in the unit to make drilling easy
        • NOTE: Use only steel tubing, do NOT use aluminum tubing products.
        • NOTE: For projects using stars, we recommend using "black pipe" with floor flanges
      • QT3 or QT4 - 1" to 2" "Black Iron" pipe with floor flange
    • Allows for 3 or 4 guy wires in each topper depending on your size and requirements.
      • QT3 has three rows of guy wire holes (3 and 4 guy wires) allowing for maximum versatility and customization with large MegaTrees
      • HolidayCoro does not recommend only connecting guy wires at the center of a support pole unless you have a 360 degree tree to support the top
      • Do not apply excessive tension on guy wires when using turn buckles, ratcheting straps or other devices intended to increase tension
    • Design allows for a variety of different star designs above the topper (see our website for pixel tree toppers)
    • All strong, weatherproof materials designed for many seasons to come
    • Friction attachment to center pole (QT1, QT2, QT7 and QT8) - for no worries about bolts popping out of slots
    • Megatree build example:
  • Included, optional and customer supplied items
    • Included
      • Topper
      • Compression screws to lock topper onto mounting pole
    • Optional (from HolidayCoro)
      • 4" Zip Ties (usually 4 per strip for top and bottom)
      • Strain Relief Clips - These strips provide a strain relief for the end of the strip at the ground when used with nails or other methods that concentrate loads on the node holes when secured
      • Center Pole Load Spreader - This 4.4" diameter, 3/4" thick plastic base allows you to mount your center pole so that the load is spread out over a larger area, preventing the pole from sinking into the ground. Additionally, there are 4 holes drilled (1 in the center of the pole and three on the outside) to prevent movement of the center pole. This item can be purchased from the optional section above on this page.
    • Customer Supplied / Purchased
      • Support Pole
        • QT1 - 3/4" EMT Conduit which can be found in the electrical isle of all hardware stores see links above
          • Actual center pole hole size: .90 inches / 22.9mm
        • QT2 / QT7 / QT8 - 1-3/8" Top Rail Fence Tubing or "Pipe" which can be found in the "Chain Link Fence" section of hardware stores (see links above). Note that multiple sections can be connected together to form longer poles.
          • Actual center pole hole size: 1.15 inches / 29.2mm
        • QT3 - 1" Hard "black" schedule 40 pipe with floor flanges (see links above)
          • None - use only floor flange to distribute load
        • QT4 - 1" Hard "black" schedule 40 pipe with floor flanges (see links above)
          • None - use only floor flange to distribute load
      • Guy Wire - Due to the large number of customer specific environments, tree heights and dimensions, it is not possible to include a "one size fits all" solution for supporting trees. The following are general suggestions to consider:
        • Number of guy wires - The QuickTree toppers have a variety of holes for different mounting options, either 3 (QT1) or 3 or 4 (QT2 / QT3). For customers that have extremely high or heavy trees should consider using all four mounting points, for regular installations, three is typically sufficient.
        • No guy wire - Only QT1 can be used in short (under 8ft), un-guyed installations with 360 degree trees - all others should use a minimum installation of three guy wires.
        • The following are common methods of guying a QuickTree topper:
          • Ratcheting Straps (tie down straps) - Commonly available at many stores (Home Depot, Lowes, Menards, Harbor Freight), in many lengths, quality and colors, tie down straps allow you to easily make adjustments to the position of your center pole to allow for the perfect angle without the need to re-position the stakes. They also allow for quick adjustments to tighten up a tree as it "settles" over time. This is the preferred method for supporting a QuickTree.
          • Para-cord / Rope - Commonly available and inexpensive. Rope can have a tendency to stretch over time and requires knotting. It does allow re-positioning of the tree.
          • Metal Stranded Rope / "Aircraft Cable" - Extremely strong but hard to work with, terminate, more expensive and not usually as flexible as other options. This method tends to be very hard to make minor adjustments to a tree. Not generally recommended.
      • Eye Bolts - Guy Wire Connection Points
        • Required for use with rope, para-cord or ratcheting straps to attach to the topper
        • 3/8" x 2" to 6" Eye Bolts - 3 or 4 per topper (Home Depot, Lowes, Menards)
        • Be sure to have two nuts - one on each side of the topper, we do not recommend using only one nut on the top.
      • Threaded Pipe Mounting Flange (optional / not required)
        • For customers that wish to either using rigid pipe for their center pole and/or for their star topper
        • QT2. QT3, QT7, QT8: Pre-marked holes for 1" Threaded Pipe Mounting Flange (Home Depot, Lowes, Menards)
        • QT2, QT3, QT4, QT7, QT8: Pre-marked holes for 3/4" Threaded Pipe Mounting Flange (Home Depot, Lowes, Menards)
        • QT2, QT3, QT4, QT7, QT8: For customers that want to use other sized flanges, there is up to 3.75" of space on the inside of the disk that can be used
        • QT2, QT7, QT8: Using a flange will partially block the 1" cable pass-through.
        • Examples of floor flange bolted installation with bottom and top flanges:


    • Customer Supplied Tools
      • Wrench (for attaching guy wire eye bolts)
      • Phillips Screw driver (for installing friction fit screws)
      • Hacksaw (used when cutting EMT conduit or top rail to length)
      • Hammer (installing nails or spikes)
  • Product Specifications
    • 6 to 16 String Topper (QT1)
      • Design for MiniTrees or small pixel trees under 10 feet in height
      • Center pole designed for use with 3/4" EMT Conduit
      • The following chart details the distribution of strings possible in different degrees of coverage on the MegaTree. Typically most MegaTrees are not a full 360 since the rear facing lights are not seen.
      • Degrees of Coverage
        (out of 360 degrees)

        Model
        QT1
        3 Slots
        Model
        QT1
        8 Slots
        Model
        QT1
        16 Slots
        Diameter at top of tree > 2.6" 3.4" 4.4"
        Center to Center Spacing of Strips > 1.3" 1.3" .8"
        180 (half) #
        S
        t
        r
        i
        p
        s
        3 4 8
        360 (full tree) 6 8 16
    • 5 to 32 String Topper (QT2)
      • Versitle topper for mid-sized trees with options up to 360 degrees
      • Designed for typical MegaTrees of 8 to 20 feet in height
      • Center pole designed for use with 1-3/8" Top Rail Fence Tubing
      • The following chart details the distribution of strings possible in different degrees of coverage on the MegaTree. Typically most MegaTrees are not a full 360 since the rear facing lights are not seen.
      • Degrees of Coverage
        (out of 360 degrees)

        Model
        QT2
        12 Slots
        One Inside Ring
        Model
        QT2
        24 Slots
        Two / Both Rows Rings
        Model
        QT2
        16 Slots
        One Outside Ring
        Model
        QT2
        32 Slots
        Two / Both Outside Rings
        Diameter at top of tree > 4.5" 4.5" 6.5" 6.5"
        Center to Center Spacing of Strips > 1.4" .76" 1.5" .75"
        160 (less than half) #
        S
        t
        r
        i
        p
        s
        5 10 7 14
        180 (half) 6.5 11.5 8 16
        (Most Common)
        200 (more than half) 7 13 9 18
        270 (three-quarters) 9 18 12 24
        360 (full tree) 12 24 16 32
        (Common)
    • 16 String Topper (QT8)
      • Designed for typical MegaTrees of 8 to 20 feet in height
      • Used as a budget option instead of the QT2 when only 16 strips and 180 degrees is needed
      • Center pole designed for use with 1-3/8" Top Rail Fence Tubing
      • The following chart details the distribution of strings possible in different degrees of coverage on the MegaTree.
      • Degrees of Coverage
        (out of 360 degrees)

        Model
        QT8
        32 Slots
        Two / Both Outside Rings
        Diameter at top of tree > 6.5"
        Center to Center Spacing of Strips > .75"
        160 (less than half) #
        S
        t
        r
        i
        p
        s
        N/A
        180 (half) 16
        (Most Common)
        200 (more than half) N/A
        270 (three-quarters) N/A
        360 (full tree) N/A
    • 10 to 64 String Topper (QT3)
      • Designed for Super-MegaTrees of 20 to 40+ feet in height
      • Center pole designed for use with 1 or 1-1/2" Black Pipe with floor flange
      • The following chart details the distribution of strings possible in different degrees of coverage on the MegaTree. Typically most MegaTrees are not a full 360 since the rear facing lights are not seen.
      • Degrees of Coverage
        (out of 360 degrees)

        Model
        QT3
        24 Slots
        One Inside Ring
        Model
        QT3
        48 Slots
        Two / Both Inside Rings
        Model
        QT3
        32 Slots
        One Outside Ring
        Model
        QT3
        64 Slots
        Two / Both Outside Rings
        Diameter at top of tree > 11" 11" 14" 14"
        Center to Center Spacing of Strips > 1.4" .66" 1.3" .73"
        160 (less than half) #
        S
        t
        r
        i
        p
        s
        10 21 14 28
        180 (half) 12 23.5 16 31.5 / 32
        (Most Common)
        200 (more than half) 13.5 26 17.5 35
        270 (three-quarters) 17 36 24 48
        360 (full tree) 24 48 32 64
    • 21 to 96 String Topper (QT4)
      • Designed for Giant-MegaTrees of 20 to 40+ feet in height
      • Center pole designed for use with 1 1/2" Pipe Flange and "Black Pipe" due to weight requirements. Center can be modified for other mounting methods.
      • The following chart details the distribution of strings possible in different degrees of coverage on the MegaTree. Typically most MegaTrees are not a full 360 since the rear facing lights are not seen.
      • Degrees of Coverage
        (out of 360 degrees)

        Model
        QT4
        Outside
        Ring Only
        Model
        QT4
        Outside &
        Inside Rings
        Diameter at top of tree > 22.8 22.8"
        Center to Center Spacing of Strips > 1.49" .73"
        160 (less than half) #
        S
        t
        r
        i
        p
        s
        21 41
        180 (half) 23 47
        200 (more than half) 27 53
        270 (three-quarters) 35 71
        360 (full tree) 48 96
    • Product Revision history
      • 13-Apr-15 Initial listing
      • 17-Jul-16 - Added QT4 design
      • 05-May-19 - Added QT8 design
      • 23-Sept-2021 - QT2 & QT8 are now produced from Nylon 66 materials
    • Custom Designs
      • Any combination, spacing diameter, mounting system or other customization
      • Minimum run cost of $275 + Materials, only one minimum unit required. Available only from Feb to August.
    • County of Origin:
      • Design: USA (Texas)
      • Manufacturing:
        • QT2/QT8 - China
        • QT3/QT4/Load spreader - USA (Texas)
      • Materials:
        • QT2/QT8 - China
        • QT3/QT4/Load spreader - USA (Texas)
    • Estimated assembly time:
      • 15 to 120 minutes (excludes PixNode Strip or controller assembly)

You might also be interested in...
Strain Relief Tab for PixNode Strips™ - Black / MISR Clip Zip Tie - 4" Black (Package of 100)
Price per Clip: $0.49

Add
Our Price: $3.99

Add
PRODUCT PHOTO: Strain Relief Tab for PixNode Strips - Black / MISR Clip PRODUCT PHOTO: Zip Tie - 4" Black (Package of 100)

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 134 Write a review »

  0 of 0 people found the following review helpful:
 
5 of 5 Mega tree topper March 11, 2024
Reviewer: Devin P Wilkes Jr from Youngstown, OH United States  
Product seems to be very straightforward. Very sturdy going to lastly very long time. Very simple to install. Very well-made a lot of thought in time went into designing it and I expect to use it for many years to come

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Mega Tree Topper January 25, 2024
Reviewer: Keith Kempke from Lebanon, OH United States  
Well constructed and adaptable for different mounting systems and tree designs.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Excellent December 27, 2023
Reviewer: Luiz Cavalheri from Brookfield, CT United States  
Excellent suppory sales and shipping

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Easy to build December 19, 2023
Reviewer: Damion Bendaw from Surprise, AZ United States  
This topper system is extremely versatile and easy to build. I have purchased two and will be purchasing more. Great product!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Q8 Topper December 11, 2023
Reviewer: Jason Richard from North Liberty, IA United States  
Excellent product, very easy to use.  Material seems very sturdy and likely to last.

Was this review helpful to you?

View All Customer Reviews